概率语言多属性群决策方法及其在新型智慧城市市民获得感评价中的应用

针对公众参与的语言信息多属性群决策问题，研究了考虑参与者满意度的概率语言多属性群决策方法。首先，根据参与者的语言评价信息确定并规范化概率语言决策矩阵。然后，对大群体进行共识分析，由最大化参与者群体的满意度构建线性规划模型，确定参与者群组的权重；构造正、负理想方案的评价向量，构建多目标规划模型，用拉格朗日乘子法求解属性权重；定义各方案的加权贴近度，并以此对方案进行排序和优选。最后，通过新型智慧城市市民获得感评价案例验证了模型的可行性和有效性。     

Highly stable dielectric frequency response of chemically synthesized Mn-substituted ZnFe2O4

The tenacity of the present study was to develop a material using an economical chemical route, having balance between magnetic and dielectric order parameters for maximum transmittance of electromagnetic waves in order to use them in shielding materials. In this context, Mn-Zn ferrites were prepared using a wet chemical based sol-gel auto-combustion technique. X-ray diffraction confirmed the pure phase formation of samples, while some impurity peaks were also present for the higher value of Mn substitution. Field emission scanning electron microscopy revealed a decrease in grain size with increasing Mn substitution. While energy dispersive X-ray spectroscopy confirmed the elemental composition of pure and Mn substituted samples, the dielectric constant, dielectric loss and tangent loss were decreased with increasing frequency and increasing Mn substitution. The complex electric modulus was found to be a function of frequency and values of complex electric modulus were increased with increasing frequency and Mn substitution. The complex impedance of RC series circuit and RC parallel circuit was also decreased with increasing both the parameters while AC conductivity was increased in the series. Dielectric frequency response was also studied for the prepared samples and the best match was found with expected results. The Nyquist and Cole-Cole plots revealed the semi-conductive behavior at higher frequency and Mn substitution also yielded the same results. The relative stability of the samples to be used as dielectric materials was also studied using Bode and Nichols plots, and a comparatively high gain margin was observed, well suitable for potential applications in electromagnetic shielding.     

Analytical formulas for complex permittivity of periodic composites. Estimation of gain and loss enhancement in active and passive composites

ABSTRACT

The asymptotic homogenization method is applied to complex dielectric periodic composites. An equivalence to coupled dielectric problems with real coefficients is shown. This is similar to a piezoelectric problem: an out-plane mechanical displacement and an in-plane electric potential establishing a correspondence principle. Closed-form formulas for the complex dielectric effective tensor in the case of a square array of circular inclusions embedded in a matrix are given. These formulas are written in terms of a real and symmetric matrix which facilitates the implementation of the computational scheme. We also get similar formulas for multilayered complex dielectric composites. The real closed-form formulas are advantageous for estimating gain and loss enhancement properties of active and passive composites in certain volume fraction intervals. Numerical computations are performed and the results are compared with other approaches showing the usefulness of the obtained formulas. This may be of interest in the context of metamaterials.     

Using a Novel and Easy-to-Use Sandwich Structure Device to Evaluate the Cooling Properties of Cool Materials

A number of cool materials have been designed and used in hot weather to minimize the heat coming from sunlight. Traditionally, solar reflectance and infrared emittance were measured to characterize the cooling properties of cool materials. However, these methods could represent the cooling property only indirectly. In this work, a sandwich structure device that can straightforwardly measure the cooling properties of cool materials was designed. Two cool materials, including high-density polyethylene (HDPE) and polyvinyl chloride (PVC), were selected to verify the device. For the purpose of comparison, UV-vis-NIR spectral characterization was also used to evaluate the cooling properties of the selected materials. The results, especially for the HDPE/Green 260 composite sample, which presents much lower solar reflectance but better cooling property, indicated that the cooling properties cannot be entirely represented by only the reflectance or transmittance, and the sandwich structure device was able to make up for this deficiency.     

Te溶剂Bridgman法CdMnTe晶体核辐射探测器的制备和表征

碲锰镉(CdMnTe)作为性能优异的室温核辐射探测器材料,可用于环境监测和工业无损检测领域。本文中采用Te溶剂Bridgman法生长In掺杂Cd_0.9Mn_0.1Te晶体,制备成10 mm×10 mm×2 mm大小的室温单平面探测器,研究了该探测器对²⁴¹Am@59.5 keV γ射线源的能谱响应。通过表征红外透过率、电阻率以及探测器能谱响应等参数,综合评定了探测器用CdMnTe晶体的质量、电学和探测器性能。结果表明,晶片的红外透过率均在55%以上,最好可达到60%。采用湿法钝化,100 V偏压下的漏电流由钝化前的9.48 nA降为钝化后的7.90 nA,钝化后的电阻率为2.832×10¹⁰ Ω·cm。在-400 V反向偏压下,CdMnTe探测器对²⁴¹Am@59.5 keV γ射线源的能量分辨率在钝化前后分别为13.53%和12.51%,钝化后的电子迁移率寿命积为1.049×10^-3 cm²/V。研究了探测器的能量分辨率随电压的变化特性,当偏压≤400 V时,探测器的能量分辨率主要由载流子的收集效率决定,而当偏压>400 V时,能量分辨率由漏电流决定。本文研究结果表明,Te溶剂Bridgman法生长的CdMnTe晶体质量较好,电阻率和电子迁移率寿命积满足探测器制备需求。     

Monodisperse Six-Armed Starbursts based on Truxene-Cored Multibranched Oligofluorenes: Design,Synthesis, and Stabilized Lasing Characteristics

A series of monodisperse six-armed conjugated starbursts ( Tr1F , Tr2F , and Tr3F ) containing a truxene core and multibranched oligofluorene bridges capped with diphenylamine (DPA) units has been designed, synthesized, and investigated as robust gain media for organic semiconductor lasers (OSLs). The influence of electron-rich DPA end groups on their optoelectronic characteristics has been discussed at length. DPA cappers effectively raise HOMO levels of the starbursts, thus enhancing the hole injection and transport ability. Solution-processed electroluminescence devices based on the resulting six-armed starbursts exhibited efficient deep-blue electroluminescence with clear reduced turn-on voltages (3.2–3.5 V). Moreover, the resulting six-armed molecules showed stabilized electroluminescence and amplified spontaneous emission with low thresholds (27.4–63.9 nJ pulse⁻¹), high net gain coefficients (80.1–101.3 cm⁻¹), and small optical loss (2.6–4.4 cm⁻¹). Distributed feedback OSLs made from Tr3F exhibited a low lasing threshold of 0.31 kW cm⁻² (at 465 nm). The results suggest that the construction of truxene-centered six-armed conjugated starbursts with the incorporation of DPA units can effectively enhance EL properties by precisely regulating the HOMO energy levels, and further optimizing their optical gain properties.     

便携式无线人体脂肪率测量仪的设计

生物电阻抗法(BIA)是一种安全非侵入式的、结果可靠有效的人体组成成分(脂肪含量)测量方法。以此为原理,设计了一款便携式无线人体脂肪率测量仪。硬件上,系统以高集成化、低功耗的阻抗测量芯片AD5933为核心,通过蓝牙实现与上位机的无线通信,大大降低了设备的复杂度。软件部分提出一种单频点小阻抗范围的增益系数校准方式,计算量小且容易实现。将新测量仪和欧姆龙体脂仪HBF-358进行对比实验,并作Bland-Altman一致性分析。结果表明,二者的相关系数为0.997。此外,该测量仪还具有易操作、小型化的特点。     

增益导引-折射率反导引大模场光纤激光器抽运技术研究进展

介绍了一种新型增益导引-折射率反导引大模场光纤的结构、基本理论以及其在光纤激光器领域的重要应用. 在综合分析了不同抽运条件下的激光输出特性以及光纤的热效应特征后, 得出侧面抽运是增益导引-折射率反导引大模场光纤的最佳抽运方案的结论; 重点介绍了增益导引-折射率反导引大模场光纤侧面抽运的理论模拟以及基于V形槽技术的侧面抽运实验研究过程, 为相关领域的实验研究提供了参考; 最后分析了实验结果与理论差距较大的原因, 并提出了改进的方向.     

基于MoO3/Ag/MoO3透明阳极的顶发射OLED的模拟计算与制备

运用传输矩阵法和正交分析法模拟计算出MoO₃/Ag/MoO₃透明电极的最佳厚度,采用镀膜实验验证模拟计算的准确性,制备了一系列不同MoO₃膜厚度和Ag膜厚度的透明电极。然后,制备了一系列顶发射有机电致发光器件:铝/氟化锂(LiF)/三(8-羟基喹啉)铝(Alq₃)/N,N'-二苯基-N,N'-(1-萘基)-1,1'-联苯-4,4'-二胺/三氧化钼(MoO₃)/银(Ag)/三氧化钼(MoO₃),来进一步验证模拟计算运用在器件制备中的准确性。MoO₃(10 nm)/Ag(10 nm)/MoO₃(25 nm)在532 nm处的透射率达到最大值88.256%,以该透明电极制备的器件与参考器件相比,性能有了明显提高,最大亮度和最大效率分别为20 076 cd/m²和4.03 cd/A,提高了18.5%和56%。器件性能的提高归因于顶发射OLED器件透射率的提高和MoO₃对空穴注入能力的提升。